The Silkland DP80 DisplayPort Cable review comes down to a specific use case: a short connection for a high-end PC and monitor that can make use of DisplayPort 2.1’s highest bandwidth tier.
Its 1.6-foot length, 80Gbps rating, and support for high refresh rates make it a focused choice for a close-set gaming desk.
Silkland DP80 Review Summary
The quick verdict

2,000+ ratings
Read Amazon ReviewsSilkland DP80 DisplayPort Cable
A 1.6-foot DisplayPort 2.1 cable for gamers pairing compatible high-end graphics cards and monitors at close range.
- VESA-certified DisplayPort 2.1 cable with an 80Gbps data-transfer rating and UHBR20 support.
- Supports uncompressed 4K at 240Hz, 8K at 60Hz, and 2K at 540Hz; DSC-enabled modes reach up to 16K at 60Hz, 8K at 240Hz, and 4K at 540Hz, 480Hz, or 360Hz.
- Backward compatible with DisplayPort 2.0 and 1.4; supports HDR10+, HDCP 2.3, 3D, and 7.1, 5.1, or 2.0 uncompressed audio pass-through.
- Gaming and display features include VRR, FEC, ALLM, DSC 1.2a, and MST for multi-monitor setups.
Pros
- 80Gbps bandwidth and UHBR20 support suit compatible next-generation display connections.
- Broad high-resolution and high-refresh-rate modes, including DSC-enabled options.
Consider before buying
- The 1.6-foot length is restrictive if the PC and display are not close together or the cable needs to follow a longer route.
- Reaching the highest listed modes depends on the graphics card, display, settings, and whether DSC is supported and enabled.
Read the full review summary
Silkland’s DP80 is a male-to-male DisplayPort cable rated for 80Gbps and VESA certified.
The listed modes include uncompressed 4K at 240Hz, 8K at 60Hz, and 2K at 540Hz; with DSC enabled, it supports up to 16K at 60Hz, 8K at 240Hz, and 4K at 540Hz, 480Hz, or 360Hz.
These are maximum supported modes, not a guarantee that every computer and display will run them.
This 1.6-foot cable is best suited to a tidy, nearby connection between a compatible graphics card and monitor. It also brings a no-latch plug design, nylon exterior, and support for VRR, ALLM, MST, HDR10+, and multichannel audio pass-through.
Check the ports and target resolution and refresh rate on both devices, and allow for the cable’s short reach before choosing it.
The buying factors
Silkland DP80 Scorecard
Editorial scores reflect listed features and buyer fit; they are not laboratory measurements or customer ratings.
Bandwidth headroom
The 80Gbps rating and UHBR20 support target very high-bandwidth DisplayPort setups.
High-refresh support
The listed uncompressed and DSC modes give buyers several demanding resolution and refresh-rate combinations to consider.
Length flexibility
At 1.6 feet, it suits nearby components but leaves little room to route around a desk or stand.
Gaming features
VRR, ALLM, FEC, DSC, and MST support address gaming and multi-monitor use, subject to device compatibility.
Build details
Triple shielding, tinned copper conductors, gold-plated connectors, and a nylon exterior are useful construction features.
Compatibility clarity
It is backward compatible with DP 2.0 and 1.4, while full UHBR20 operation depends on both connected devices.
Key Features and Specifications of Silkland DP80
- VESA-certified DisplayPort 2.1 cable with an 80Gbps data-transfer rating and UHBR20 support.
- Supports uncompressed 4K at 240Hz, 8K at 60Hz, and 2K at 540Hz; DSC-enabled modes reach up to 16K at 60Hz, 8K at 240Hz, and 4K at 540Hz, 480Hz, or 360Hz.
- Backward compatible with DisplayPort 2.0 and 1.4; supports HDR10+, HDCP 2.3, 3D, and 7.1, 5.1, or 2.0 uncompressed audio pass-through.
- Gaming and display features include VRR, FEC, ALLM, DSC 1.2a, and MST for multi-monitor setups.
- Male-to-male DisplayPort connectors use a no-latch design; the cable is 1.6 feet long.
- Construction details include 28AWG tinned copper conductors, triple shielding, 24K gold-plated connectors, and a nylon exterior.
Pros and Cons of Silkland DP80
Pros
- 80Gbps bandwidth and UHBR20 support suit compatible next-generation display connections.
- Broad high-resolution and high-refresh-rate modes, including DSC-enabled options.
- Gaming-oriented features include VRR, ALLM, FEC, and MST support.
- No-latch connectors may be easier to unplug in a tight space, while the nylon exterior and triple shielding add practical build details.
Consider before buying
- The 1.6-foot length is restrictive if the PC and display are not close together or the cable needs to follow a longer route.
- Reaching the highest listed modes depends on the graphics card, display, settings, and whether DSC is supported and enabled.
- The no-latch design may be less appealing to buyers who prefer a locking connector.
Who Should Buy Silkland DP80?
Good fit
Consider the Silkland DP80 if your desktop and monitor sit close together and both have DisplayPort connections.
Its 80Gbps rating and support for UHBR20 make it a reasonable match to investigate for a high-end display setup, especially when you want one cable that supports high refresh rates and gaming features such as VRR and ALLM.
Before buying, check the exact display input, graphics-card output, and target mode in both devices’ specifications. For modes listed with DSC, confirm that both ends support the required display features.
Also measure the route between the ports, including any bends around the monitor stand: 1.6 feet can be convenient for a compact layout but unforgiving if the connection has to travel farther.
Who should skip it
Choose another length if the PC and monitor are separated by more than a short direct run, or if you need extra slack for moving or repositioning either device.
This is a poor fit for a setup that connects over HDMI, or for one where either device lacks DisplayPort.
If you do not need the cable’s high-bandwidth modes, compare simpler options that meet your actual resolution and refresh-rate requirements.
What the Silkland DP80 Cable Means for a Gaming Setup
Bandwidth and display modes
The 80Gbps rating is the cable’s headline advantage, but the practical mode comes from the whole signal chain.
The source and monitor must support the relevant DisplayPort version and features, and some of the highest resolutions and refresh rates depend on DSC. Treat the mode list as compatibility targets to verify against the devices you own.
A short run is a layout decision
A 1.6-foot cable can reduce excess slack when a PC sits directly beside or under a monitor. That same length leaves little tolerance for routing behind furniture, around a monitor arm, or to a tower placed farther away.
Measure the actual path rather than relying on straight-line distance.
Gaming and multi-display features
VRR, ALLM, FEC, and DSC are relevant to modern gaming displays, while MST can support multi-monitor arrangements when the devices and setup support it.
The cable alone does not establish that a particular refresh rate, synchronization feature, or multi-screen configuration will work; confirm support across the connected equipment.
Construction and connector handling
Triple shielding, 28AWG tinned copper, gold-plated connectors, and a nylon exterior describe a build aimed at a stable, durable connection. The connector has no latch, which can make removal simpler where access is tight.
Consider whether a non-locking plug fits how often you connect and disconnect your display.
Alternatives to Silkland DP80
Computer DisplayPort Cables alternative

7,000+ ratings
Read Amazon ReviewsSilkland 54Gbps DisplayPort 2.1 Cable, 10 ft
Choose the 10-foot model if you need substantial reach and its listed bandwidth and modes fit your display.
Keep the DP80 in consideration when the connection is close and you specifically want its higher 80Gbps rating; the longer cable trades that bandwidth tier for reach.
- This Silkland cable is 10 feet long and rated for 54Gbps.
- Its listed modes include 4K at up to 240Hz and 8K at 120Hz, with 16K at 60Hz using DSC; it also has a braided exterior and supports DisplayPort versions down to 1.0.
- The DP80 is a 1.6-foot, 80Gbps cable with support for UHBR20 and higher listed modes, making it suitable for a very short run when both devices can use those capabilities.
Is Silkland DP80 Worth It?
The Silkland DP80 is worth considering for a compact gaming setup when both the graphics card and monitor support DisplayPort and the cable can reach comfortably.
Its 80Gbps rating, high-refresh support, and gaming features are strong reasons to shortlist it for compatible equipment.
Measure the cable path and verify device support before choosing it. Its short length is the main practical constraint, and the most demanding modes depend on the capabilities and settings of the connected devices.
Your review at a glance

2,000+ ratings
Read Amazon ReviewsSilkland DP80 DisplayPort Cable
A 1.6-foot DisplayPort 2.1 cable for gamers pairing compatible high-end graphics cards and monitors at close range.
- VESA-certified DisplayPort 2.1 cable with an 80Gbps data-transfer rating and UHBR20 support.
- Supports uncompressed 4K at 240Hz, 8K at 60Hz, and 2K at 540Hz; DSC-enabled modes reach up to 16K at 60Hz, 8K at 240Hz, and 4K at 540Hz, 480Hz, or 360Hz.
- Backward compatible with DisplayPort 2.0 and 1.4; supports HDR10+, HDCP 2.3, 3D, and 7.1, 5.1, or 2.0 uncompressed audio pass-through.
- Gaming and display features include VRR, FEC, ALLM, DSC 1.2a, and MST for multi-monitor setups.